Custom Colored Glass Lenses for Airfield Lighting

BO-Glass developed colored glass lenses for a U.S. distributor of airfield lighting components. The project combined glass formulation, molded optical patterns and sample verification to address inconsistent color quality and long sourcing lead times.

Clear, red, green and amber ribbed glass lenses for airfield signal lighting
Clear and colored glass lenses with molded ribs, developed for the customer's airfield lighting program.

The Customer's Challenge

The customer needed a dependable source of glass domes and lenses for its runway and taxiway lighting component range. Color consistency mattered alongside dimensional fit: a change in the glass formulation could alter both the transmitted color and the amount of light reaching the intended viewing direction.

The brief therefore focused on repeatable color, controlled transmission and production to the customer's drawings. BO-Glass's scope was the custom glass component, with samples supplied for the customer's optical evaluation before production.

Developing the Color in the Glass

According to the project record, the lenses used a high-borosilicate base with metal-oxide colorants incorporated into the melt. The color was developed through the glass composition rather than applied as a surface coating.

Sample trials refined the balance between hue and transmission. Batch composition and melting conditions were adjusted, then sample lenses were produced for review. This allowed the team to evaluate the color in the intended lens geometry rather than judging the raw glass alone.

Glowing molten glass gather being transferred to a forming mold
Molten glass transferred to the forming mold during production.

Color Samples and Molded Optical Details

The sample photographs show red, green, amber and clear glass sectors positioned side by side. Their contrasting colors make the molded ribs and surface profiles easier to compare. The customer's drawing defined the component geometry and optical pattern for each part.

Pressing and Annealing for Production

Custom Pressed Geometry

After the sample formulation was agreed, production lenses were pressed to the customer's dimensional drawings. The tooling formed the component profile and its optical ribs together, supporting consistent geometry across the order.

Annealed Glass

The lenses were annealed to relieve internal stress after forming. This project used annealed glass rather than tempering, in line with the customer's preference for the optical components in this program.

Batch of green ribbed glass lens components arranged in separators
A green glass lens batch arranged in individual separators.
Red and amber glass lenses on production trays
Red and amber lenses on production trays.

Sample Review and Transmission Checks

Illuminated samples supported review of the glass with a light source. The production record also includes an LS182 transmission-meter spot check on a green lens, providing a broadband transmission reading for that sample.

Sample evaluation focused on the interaction between lens color, transmission and the intended light source. The customer's own color and transmission verification formed the basis for accepting the initial samples.

Red glass lens illuminated inside a reflective enclosure
An illuminated red glass sample under review.
Green glass lens held at an LS182 broadband transmission meter
LS182 broadband transmission spot check on a green glass sample.

From Initial Samples to More Than 20 Part Numbers

According to the project record, the customer accepted the initial samples after its own color and transmission verification. The supply program subsequently expanded to more than 20 distinct part numbers covering different colors, sizes and molded patterns.

The project established a repeatable route from custom glass formulation to pressed and annealed components, with sample review connecting production choices to the customer's lighting requirements.

Red, green and blue airfield signal lights at dusk
Application reference: colored signal lighting in an airfield environment.

Contact Us

Discuss Your Custom Glass Project

Share your drawing, photos or dimensions, together with the intended use and target quantity. We will review your requirements and discuss the next steps.

Sales Enquiries

Email sales@bo-glass.com with your part description, intended use and target quantity.

Send Your Design

Use the form to upload a drawing or describe an existing part. Mark critical dimensions and tell us which surfaces or features matter most.

 

Request a Custom Glass Quote

 

Upload a drawing or share dimensions, quantity, intended use and finish. Include any heat, pressure or chemical exposure.


    One file, up to 10 MB.
    Accepted formats: PDF, JPG, JPEG, PNG, STEP, STP, DWG and DXF.

     

    Your drawings remain confidential.

    We use the contact details you provide to respond to your enquiry. See our Privacy Policy for more information.