Custom Glass Lenses for Underwater Explosion-Proof Luminaires

BO-Glass developed a custom domed glass lens for a U.S. lighting manufacturer’s underwater luminaire project. The work focused on impact resistance, hydrostatic pressure performance and sealing-surface precision, with the glass designed for integration into the customer’s complete luminaire.

Clear domed glass lens with a broad circular sealing flange, shown in profile on a blue grid
The finished glass component combines a curved dome with a flat peripheral sealing flange.

Three Requirements, One Glass Component

The customer needed a lens that could address mechanical impact and sustained underwater pressure while fitting the housing’s sealing interface. Each requirement affected the others: glass thickness and curvature influenced the lens structure, while the flange needed a precisely controlled surface for the gasket or O-ring.

7 J Impact Requirement

The lens had to withstand the specified impact test without visible cracking or chipping.

Underwater Pressure

The glass and its assembled sealing interface needed to maintain integrity under hydrostatic load.

0.01 mm Sealing Flatness

The bottom sealing surface required precision finishing beyond the as-pressed condition.

A 10 mm Domed Glass Design

The project used a 10 mm glass thickness and a curved dome profile. The geometry was selected to distribute loads across the lens rather than relying on thickness alone.

A broad flange provided the interface with the housing seal. Its shape and finished surface were treated as part of the structural and sealing design, alongside the dome itself.

Front view of the transparent circular dome lens and its surrounding sealing flange
Front view of the dome and the continuous circular flange used at the sealing interface.

From Custom Tooling to a Precision Sealing Surface

Custom tooling established the dome and flange geometry during hot forming. Controlling the formed profile provided the foundation for the subsequent strengthening and finishing work. The production images below show the forming equipment and heated glass at the press.

Circular dome-forming tooling mounted in the glass press
Dedicated circular tooling supports the required domed profile and peripheral flange.
Heated glass glowing red in circular forming tooling beside gas burners
Heated glass at the forming station.
Glass press workstation with circular tooling and heated glass during production
A wider view of the press workstation during hot forming.

Thermal Strengthening

The project incorporated physical tempering to improve resistance to mechanical loading. Strengthening, component geometry and the sealing interface were considered together as part of the manufacturing plan.

Precision Sealing Finish

Precision grinding addressed the sealing-surface variation left by pressing. The project record specifies diamond grinding with coolant and flatness measurement to achieve the required 0.01 mm sealing surface.

Reported Project Results

According to the project record, the finished lenses met the impact and sealing requirements below. Sealing-surface flatness was also checked on each production piece.

CheckProject ValueReported Result
Impact7 JNo visible cracks or chips after testing.
Hydrostatic Pressure1.5 MPa for 24 hoursNo leakage in the tested assembly.
Sealing-Surface Flatness0.01 mmVerified by production inspection.

These results apply to the tested glass and assembly. Final luminaire qualification depends on the complete design and the specified tests.

Glass Engineered for the Complete Assembly

This project brought together dome geometry, glass thickness, thermal strengthening and a precision sealing surface. The resulting component addressed the customer’s defined impact, pressure and fit requirements within one glass design.

The assembled luminaire illustrates the intended application of the lens. BO-Glass’s contribution in this case was the custom glass component.

Yellow underwater luminaire with a clear round glass lens installed over the LED array
Application reference: the glass lens installed in the customer’s luminaire.

Contact Us

Discuss Your Custom Glass Project

Share your drawing, photos or dimensions, together with the intended use and target quantity. We will review your requirements and discuss the next steps.

Sales Enquiries

Email sales@bo-glass.com with your part description, intended use and target quantity.

Send Your Design

Use the form to upload a drawing or describe an existing part. Mark critical dimensions and tell us which surfaces or features matter most.

 

Request a Custom Glass Quote

 

Upload a drawing or share dimensions, quantity, intended use and finish. Include any heat, pressure or chemical exposure.


    One file, up to 10 MB.
    Accepted formats: PDF, JPG, JPEG, PNG, STEP, STP, DWG and DXF.

     

    Your drawings remain confidential.

    We use the contact details you provide to respond to your enquiry. See our Privacy Policy for more information.